KOMODO 6K S35 FAQs

Topics covered on this page:

Setup and Configuration

Image

Post

RED Control

Setup and Configuration 

Can I use RF lenses on the KOMODO? 

KOMODO does not currently support the electronic control of Canon RF lenses. This means that neither focus nor aperture can be adjusted while attached to the KOMODO. Third-party lenses that allow manual control of focus, iris, and zoom are compatible with KOMODO. 

What lenses can I use on KOMODO? 

KOMODO leverages the RF-style lens mount to allow it native-level performance with Canon EF lenses, but unlike a true EF mount it can be adapted to many other lens mounts such as PL, Leica M, and Nikon F. 

What lens adapters can I use on KOMODO? 

Most adapters designed for the Canon RF mount will work with the KOMODO. However, it is not recommended to use any adapter with an AF Confirm Chip. AF Confirm Chips will not add any additional functionality to your non-EF Lenses on KOMODO and have been known to cause communication errors with the KOMODO. 

Please see the full list of RED approved third party accessories on our KOMODO compatible lens mounts article.

What CFast media is approved?

Please see the full list of RED approved third party accessories on our third party accessories page.

What CFast readers are approved?

Please see the full list of RED approved third party accessories on our third party accessories page.

What batteries are approved?

Please see the full list of RED approved third party accessories on our third party accessories page.

Will my existing RED accessories work with KOMODO? 

The KOMODO does not support the use of existing RED EVFs, LCDs, or anything requiring power from the camera. 

I have a third-party device that I used to control my previous REDs; will it work with KOMODO? 

KOMODO has a new 9-PIN EXT connection on the rear. While this connector can break out into a 4-PIN CTRL terminal like on DSMC2 bodies, KOMODO uses the updated RCP2 protocol. Any device designed for DSMC2 or earlier will need updating from the original equipment manufacturer to communicate with KOMODO. 

How do I update my camera firmware? 

Visit red.com/downloads to acquire the latest firmware version for your camera. Firmware installation instructions appear under the firmware release notes or within your camera’s Operation Guide. 

When do I need to calibrate the sensor? 

  • When shooting in an environment where the temperature is significantly different (+/-30° F...) from the current calibration. The T in the T/E Status Bar indicator will turn yellow.  
  • After an extreme change in exposure time (+/–1/2 sec). The E in the T/E Status Bar indicator will turn yellow.
  • After each firmware upgrade. 

Why is my top LCD not responding to touch input? 

Check to make sure the LCD is not locked by simultaneously pressing both the up and down arrow buttons to toggle the lock.

Why am I getting an unapproved battery warning with genuine Canon batteries? 

This may occur after the batteries have been completely depleted or when newly opened from the box. Please fully charge the batteries either using the camera or the original equipment manufacturer’s charger. 

Why is the audio menu is grayed out and inaccessible? 

If your Project Frame Rate and Recording Frame Rate do not match, audio is not recorded in the camera and the Audio Menu is inaccessible. Match the Project Frame Rate and Recording Frame Rate to access Audio. 

Why is the autofocus menu is grayed out and inaccessible? 

Autofocus only works with Canon EF lenses using the Canon EF to EOS R Adapter. Please check to make sure your lens’s Focus Mode Switch is set to AF

Why am I not getting video signal out of my SDI port? 

Check that Menu > Monitoring > SDI > Resolution is set to a resolution compatible with your monitor. Most camera-top monitors can only accept an HD signal and not 2K, UHD, or 4K. 

Why do not see video signal in RED CONTROL? 

In the camera menu, check that Menu > Monitoring > Live Stream > Enable is active. Then, check that the RED CONTROL’s Preview is enabled by toggling the second header button from the right. 

Image 

How should I judge exposure on the camera? 

The histogram, exposure meters, and false color tools can assist in attaining a proper exposure. The RGB Exposure meter indicates if any Red, Green, or Blue pixels are clipped in the shadow or highlight region in the frame. An ideal exposure would have a balanced histogram and no Red, Green, or Blue exposure indicator lights active. 

When should I use HQ, MQ, and LQ R3D qualities?  

The latest evolution of REDCODE is optimized for KOMODOallowing users to continue unlocking unbelievable image capture potential and creative flexibility with a new simplified user experience. We recommend using the available options in the following scenarios:

  • HQ is perfect for VFX, extremely detail scenes, and stills from motion. 
  • MQ is great for cinema and high-end TV. 
  • LQ is ideal for TV, online content, documentary, interviews, and long takes. 

Why is the “T” indicator yellow or red? 

When “T” is yellow or red, it indicates that the camera requires sensor re-calibration. 

Why is the “E” indicator yellow or red? 

When “E” is yellow or red, it indicates that the camera requires sensor re-calibration.

How do I load LUTs into the camera? 

Insert a RED Approved CFast Card into your computer, ensuring that your Card Reader is switched to Read/Write access if applicable. Create a folder on the root directory of the CFast card titled “luts” and drop all compatible cube LUTs into that folder. Please note the camera accepts 17x17x17 and 33x33x33 sized LUTs. Eject the CFast card from your computer, insert it into the camera, navigate to Menu > Image / LUT > 3D LUT > On-Media LUTs, and import all desired LUTs. 

I have loaded a LUT into the camera, but it looks overly saturated and high contrast – why?

KOMODO accepts two kinds of 3D LUTs: Creative LUTs and Technical LUTs. 

  • Creative LUTs are LUTs that adjust the contrast and color of an image, but do not include any color space transforms as they are designed for use in an IPP2 Color Managed Workflow. These LUTs, when put in camera, can be used regardless of the viewing destination, they are compatible with both SDR, HDR, and Wide Gamut imaging. 
  • Technical LUTs are much more limited in that they are built to specific viewing destinations and are locked into the space they were designed for. Technical LUTs include the Color Space and Gamma transforms from REDWideGamutRGB/Log3G10 to the intended viewing space, and for that reason the camera’s Output Color Space must be set to REDWideGamutRGB to view them properly. 

If you are seeing an improperly saturated image, it is most likely because you have a Technical LUT but have not selected REDWideGamutRGB under Output Color Space, resulting in a doubling of the output transforms.

Post 

What software will accept KOMODO footage? 

Many non-linear editing systems (NLEs) can open and edit RED footage. Each NLE version may have specific compatibility requirements, such as camera firmware version or camera type. Before shooting, check all compatibility requirements. The following programs can be used to open and/or edit R3D files: 

  • REDCINE-XPRO: RED's proprietary application. Download REDCINE-X PRO for Windows or REDCINE-X PRO for Mac from www.red.com/downloads. 
  • Adobe Premiere Pro
  • Assimilate (Scratch)
  • Autodesk (Flame)
  • Avid Media Composer
  • ColorFront Transkoder (Beta)
  • DaVinci Resolve 
  • Edius Pro 
  • Filmlight (Baselight)
  • Final Cut Pro X: Requires you to download the RED Apple Workflow Installer from www.red.com/downloads. 
  • Foundry (Nuke)
  • Vegas Pro 
  • Adobe Photoshop: Can open .R3D files, however, you must download the RED Adobe Photoshop Installer for Windows or RED Adobe Photoshop Installer for Mac from www.red.com/downloads. 

What is the lock on the back of my RED CFast 2.0 Reader? 

This is a Write Protect switch, which prevents your computer from writing to the card when it is mounted. This helps preserve your card’s integrity when connected to systems that index attached drives. We recommend leaving the switch in the locked position and only recommend switching to read/write when necessary. 

What are CFast 2.0 cards formatted as? 

The camera supports exFAT as the file system for the media card to accommodate larger files and data rates. exFAT is supported both on macOS and MS Windows. 

Why does my KOMODO footage come into my post software looking flat and desaturated? 

KOMODO uses RED’s proprietary IPP2 color space and gamma curve – REDWideGamutRGB and Log3G10. This provides the most flexibility as a starting point for grading, but you can use a 3D LUT to bring the footage into a color space and gamma curve for a more finished look. 

Do you have any recommendations for configuring DaVinci Resolve? 

The Decode Quality in DaVinci Resolve is automatically set to Half Res, which is great for prioritizing smooth, realtime playback. However, this Decode Quality will result in a softer, noisier image and may introduce artifacts such as moiré. We recommend changing the Decode Quality to Full Res. Premium to see the truest representation of your image. 

RED CONTROL

How do I connect the app to the camera? 

Your device and camera must be on the same network. In camera, enable WiFi via Menu> Communication. 

What are the differences between Ad-Hoc and Infrastructure modes? 

Ad-Hoc Mode uses the camera as a hotspot. The default password to connect from your device is the same as the SSID network name, which is also your camera serial number. 

Infrastructure Mode joins an existing network and is recommended whenever possible to help ensure a stronger connection. 

What are the differences between 2.4 and 5 GHz networks? 

In general, 2.4 GHz has more range, but the band may be more crowded with other devices, especially on busy setsGHz is faster but does not like obstacles like walls. 5 GHz is always recommended for live streaming video.

Can the live stream show tools like false colors or focus peaking? 

The live stream can only show a clean image, as no overlays are sent from the camera on that image path. 

Can I use RED CONTROL and the live stream feature with a DSMC2? 

No, it is a new communication protocol and only the KOMODO has a dual band WiFi chip and required hardware to offer live stream. 

You can use the 3rd party app 'foolcontrol' to control your DSMC2 or RANGER camera over WiFiethernet, or serial. 

Why am I having issues connecting to the camera? 

Typing a password on the mini on-screen LCD keyboard can be tricky. Make sure you pay extra attention to your SSID and password case when entering it. Make sure your SSID name or password do not use special characters that may not be available in the camera.

Why am I having connection problems or interference?

In Ad-Hoc mode, you may have to turn on airplane mode to stay connected to the camera WiFi or any other network without internet access. 

2.4 GHz may be crowded in cities, on set with other accessories using that band, or in areas with a high number of mobile devices. Try changing to a different channel.

What characters are accepted for a SSID / network name?

ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz0123456789 -=[];',.!@#$%^&*()_+{}:<>?"

What characters are accepted for a password?

ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz0123456789 -=[];',./!@#$%^&*()_+{}:<>?"\`|

Was this article helpful?
1 out of 1 found this helpful
Have more questions? Submit a request

Comments

0 comments

Article is closed for comments.